Baitcasting reels are better than spinning reels in both fresh and salt water.
Different companies manufacture this type of fishing reel. It remains faultless for months but needs maintenance when its spool gets slower.
In this article, we have discussed the answer to the most common question of a fisherman “How Can We Do Baitcasting Reel Maintenance?”.
Steps for Baitcasting Reel Maintenance
- Clean the spool with a cloth and with some soapy water if it is needed. Remove all the dirt and debris present in the spool line.
- Open the slide or release the side panel to disengage spool fixing. Examine all its parts and if there were some cranks or wears you would replace it with new features.
- Get rid of all the dust from the visible parts related to spool operation with a brush.
- Oil the undamaged parts that are called oils.
- Next, take out the handles for examination and cleaning. Lubricate hand slots.
- Get access to the inside of the reels. Remove grease from internal parts. Apply oil on different reels as needed. Unscrew the reel with the help of a screwdriver
Parts That Need Regular Oiling
- Bearing in spool
- Spools axis inside driver pinion
- The metal disk at the friction brake
- Sliding parts and non-spool bearings
Warnings
- Do not apply heavy force if some parts don’t get loose
- If your reel is having a hard time, check the manufacturer’s user manual.
- Examining the spool can tell about serious problems.
- Protect your eyes and hand from oil and grease.
- Avoid prolonged contact with your hands.
Do’s for Baitcasting Reel Maintenance
- Remove line after deep ocean fishing to wash down spool or if intending to keep for long time storehouse
- Avoid placing your roll on boat side rod holders when the boat is traveling to help splashes of ocean water
- Put 1- 2 drops of oil painting on the main shaft, line comber, handle clump comportments, drive gear compartments, and screws after 2- 3 times operation
- Shoot for servicing every six months if the roll is being used constantly
Don’Ts for Baitcasting Reel Maintenance
- Loosen cast control and drag before washing as water might access the body
- Rinse overhead baitcasting roll on high-pressure water
- Dip or soak your roll in freshwater
- Place directly under the sun after washing
- Wash your reel in upside down position
Baitcasting Reel Manual
Utmost fishers start by fishing with spin cast or spinning reels, which are relatively easy to use and serve well in various fishing situations. Once they gain further experience, some fillers want to use a roll that is a little more advanced, offering further inflexibility in terms of homemade adaptation. While baitcasting reels take time for fillers to get used to, they eventually become the preferred roll of numerous anglers.
For the proper working of the reel, we must go through the baitcasting reel manual.
Particulars You’ll Need According to the Baitcasting Reel Manual
- Baitcast rod and roll
- Fishing line
- Fishing lure
- Scissors
Step 1
Set the baitcasting reel up with a baitcasting rod. A baitcasting rod is fluently linked by looking at the handle. However, it’s a baitcasting rod, If there’s a detector-shaped piece of plastic below the handle. Attach the roll to the rod and hold it to ensure it’s comfortable and feels good in your hands.
Step 2
String fishing line onto the rod and roll. You will thread the rope through the companion from the rod tip to the reel and also fit the end of the cable into the roll’s line companion, a plastic or essence hole on the edge of the reel. Roll the end of the line around the rolling spool doubly, and tie a knot, so the bar is tightly attached around the spool. Reel line onto the spool until the line is near the hem of the spool. Will cut the line so that 12 elevation hangs off the top of the rod.
If you are interested in knowing about Baitcasting Line Setup, then read out the article on this link.
Step 3
Attach bait to the end of the fishing line.
Step 4
Acclimate the drag on the baitcasting roll by turning the star-shaped piece on the reel’s handle. Rotating it clockwise tightens the drag; counterclockwise loosens the drag. The drag should be tight enough that an establishment and steady pull is needed before the drag will release the line.
Step 5
Set the roll’s resistance medium. On utmost baitcasting reels, the resistance is controlled by a dial on the roll’s side opposite the handle. A setting of” 0″ indicates there will be no resistance, while a” 10″ means there will be the highest resistance quantum. Less resistance is better for long casts or fishing with light lures. Still, the threat of counterreaction increases as resistance is dropped. You are starting with the resistance set at the halfway point. As you become more confident in the reel, lower the resistance.
Step 6
Hold the roll in your dominant hand and press on the thumb bar of the roll until it clicks. The spool will now turn freely, so it’s essential to use your thumb to put pressure on the spool to stop it from rotating. Snare the reel’s handle with your contrary hand and bring the rod over your shoulder in a casting stir.
To cast the bait into the water, put the rod forward. Move your thumb off the spool as the rod tip passes from your shoulder. Remove the thumb off the spool as the baits move through the air. When the casting lure is about to hit the water, press down on the spool to stop it from spinning. Turn the roll handle clockwise to begin reeling your lure back.
Baitcasting Reel Magnetic Brakes
A baitcasting reel magnetic braking system works on the conception of Lenz’s law, which works on the opposing forces of the attractions and the spinning spool. Glamorous boscage on baitcaster roll the baitcasting reel magnetic brakes system is contained in the side plate of the roll on the contrary side to the handle. However, inside the side plate, there’s a series of little round attractions. On the outside of the side plate is a dial, and when you turn this dial, it’ll move the attractions closer or further down from the spool, creating a stronger or weaker magnetic force.
Turning the dial-up to the loftiest number (10 for illustration) will move the attractions closest to the spool and produce the strongest stopping for on the spool. Set the dial back to the smallest number (1), and n will weaken the glamorous force, and the spool will continue to spin further freely.
The one issue about baitcasting reel magnetic brakes that some further educated druggies of baitcaster reels don’t like about magnetic brake systems is that you can noway turn them off. You can set the dial to the smallest number, moving the attractions farther down from the spool. But it still leaves a small quantum of magnetic force being applied to the spool at all times.
Still, or just starting out using a baitcaster reel with a magnetic brake system, you won’t need to worry about this, and a glamorous boscage system is veritably effective if you’re an angler.
Baitcasting Reel Making Noise
One of the most common issues regarding baitcasting reels was a clicking or grandly-pitched noise passed during the case. However, keep reading for some sapience on how to remedy it, If your baitcasting reel making noise you’re presently dealing with.
People often sweat this problem concerning the comportments, but the compartments aren’t the cause. When comportments go wrong, they don’t make noise but will instead produce an internal, rough clicking. Generally, the noise occurs when people are diligently using the roll and tends to get worse as they do so. Noises like that are caused by a commodity rubbing a face; in this case, It means the roll’s thickets.
Reels with centrifugal thickets have plastic or fiber tabs that rub the innards of a boscage ring. These must be waxed, or they’ll end up rubbing against a dry face and making noise. This noise is created, and such an issue also reduces casting distance. When a dry polyester tab rubs a dry boscage ring, the disunion is much further than when it’s waxed, and the ends of the tabs can indeed melt.
Still, it’s good practice to wipe some roll oil painting around the inside of the boscage ring at least once a month, If you have a roll with centrifugal thickets. Many drops of cotton tar are the way to do it. Also, it’s wise to open the side cover to oil paint your thickets constantly. Likewise, while having your reels serviced a time formerly is a great thing, they will still need some attention from you between services. It’s good to keep a small bottle of roll oil painting and a tube of grease along with some cotton hearties as an exigency service tackle, or you can buy a roll drawing tackle to keep on hand.
These simple ways can help maintain optimum trustability from your reels between services. Keeping them clean and smoothly waxed will also help the need to replace corridors during periodic servicing, for which your portmanteau will be thankyou. However, it may be time to check your tickets, If you’ve noticed a high-pitched noise while using your roll. Keep them waxed and make it a habit of doing so constantly, and you’ll notice a longer shelf life on your reels.
1. Baitcasting Reel Modifications
Spool control: Spool is an important factor in baitcasting reel modifications. if your spool is too loose, you have to suffer backlash in early casting. Before starting casting or doing anything else, tightens your spool control knob by turning it in an anti-clockwise direction. Now hold your bait, depress the clutch lever, and if your spool has tightened to maximum, it should dangle in the water before going to the ground.
No matter how smoothly it is going, it will backlash, so try to thumb the spool before it reaches the ground; this is called active braking. The next step is to release mention on the spool control knob unless the bait falls freely. But in such a manner that you can easily control the backlash with minimal active brake. If your spool is too loose, it will cause difficulty in casting. But if it is too tight, it will not be able to cast at a long distance. So you have to choose a center field for bait casting·
Braking system: after setting the spool knob, the next step is to adjust the braking system. Start by maximizing the setting, as it will help you to develop and understand how the braking system works and affects the cast. It helps to control spool rotation.
Select a target in your backyard, such as a tub or bucket, about 10 to 15 feet away. Your first try would be easy and gentle flips, vibratory pendulum motion, and a simple drop of the spool line. Remember, your braking system is supposed to be at maximum speed. If you are having a problem getting your target, it is due to your braking system being set to maximum.
You are slowing the forward movement of the bait during the second part of your cast. If you are having difficulty reaching your target, you might be supposed to add more force to the cast, which can cause a lot of forwarding movement in the “early part.” Your braking system faces fights in the second part of your cast, causing a backlash or birdnest.
2. Educated Thumb Is an Essential Factor
Educated thumb plays a vital role in baitcasting reel modification. If you are facing trouble with backlash after landing the lure, it is due to a late in the thumbing process during the third part of your cast. Focus on the path of the lure. There is a time when the bait reaches its highest position. At this moment, thumbing is too essential; thumbing your spool slows down its movement.
If you thumb too fast, you will lose distance, but if you thumb too late, you will backlash.
3. Battling the Bird’s Nest Is Essential
Baitcasting reel modifications will help you to lessen bird nests The easiest way to battle bird nests is to keep an eye on the spool. Look for all irregularities and difficulties in the line on the spool and solve them on the spot. Clear that the line is always around neatly and tightly. The line should be neat and untangled and not wounded loosely on the external corners or center of the spool, and there should not be many ups and downs.
When a backlash happens, do not panic, be calm, and do not allow frustration to spoil your casting. Trap the spool with your thumb and pull the line towards yourself. Usually, the backlash will solve as you pull out the line.
Conclusion
All the reels want maintenance after a few months or years. You must think your revolution needs to care if your spool line is getting slower. To maintain or repair them occasionally when needed.
It would be best if you preferred round reels over spinning wheel or low profile reels as they have high gear ratios and extensive spool line.
If you are looking for a Guide about Baitcasting Reel for Saltwater Jigging, then click on this link.
FAQs
Q1: Which parts of the reel need lubrication?
Ans: Bearing in spool
Spools axis inside driver pinion
The metal disk at the friction brake
Sliding parts and non-spool bearings
Q2: Why do reel parts need to be maintained or replaced?
Ans: Everything needs maintenance after time for its proper working. When dust or debris gets stuck in reel parts, you must remove it for the appropriate functioning of the reel.